A Decorated Render

During the spring I began the creation of a Modern modelled render – not pargetting, but neither strictly sgraffito. In actual fact not modelled at all but carved into the hard surface of the render, which itself was applied to straw bales held within a modular cassette based superstructure forming the walls of a science block built for a girls School in Bath.

A complete tangential detour from the repair and conservation of old buildings and their lime surfaces which I am known for within the Cotswold area.

The design was visualised by architects, White Design of Bristol, whilst I was asked to devise the methodology and bring about realisation. The plan was to depict a DNA double helix spiralling horizontally the full 7 metres x 45 metres of the front and side elevations.

The pattern itself was transferred from 20 architects drawings each showing about a 3.5 x 3.5 metre square section .

Due to the client requiring to see a trial section modelled onto the actual render we chose one of the more complex pieces which happened to be part way along the elevation – at this stage the client could still cancel the project so there was a possibility that the rejected trial would have to be re-rendered.

 I should just say at this point that the render was a proprietary premixed dry mortar sprayed onto the surface and scoured to a textured finish with a basket float, so re-rendering would have to start and finish at the nearest expansion joints that had been incorporated into the building.

However on the strength of the test panel the scheme was accepted. Of course, we had not started in a logical place so the pattern had to spread out either side of our starting point. I wanted to draw the entire DNA before cutting but one section had been cut already so there was some trepidation as to weather the pattern would indeed connect together; whether the diagonal ribbons were at the exact angle for the crossing points to be in the correct places and so on.

 There was, however, no need to worry as our marking out had been accurate enough for the pattern to be continued and developed along the building without any adjustment or correction.

 I had decided that the pattern needed to be carved in low relief as any applied pattern would be at risk of being knocked off the render if someone rubbed against it, also there are many areas within the render which would have tended to catch water. The pattern had to be shown as being 3 dimensional because the DNA twists around an axis and has a radius in this case of 3.5 metres and although the pattern does not accommodate any perspective it still needed to show the ribbons crossing each other. There was not much depth of render available but only a 1mm step between the 3 planes were required for the effective 3D depiction, thereby requiring a maximum depth of 4mm to be carved.

 After marking out the pattern it was colour coded with chalk so we knew exactly the depths each part would be carved to.

 Foreground ribbon 2mm

Middle ground base pairs and hydrogen bonds 3mm

Background ribbon 4mm

Once colour coded, the pattern was carved with hand tools. When the whole scheme had been carved the cut surfaces were rendered smooth and the edges sharpened using a lime putty fine stuff. This finishing plaster created a smooth surface which contrasts with the open texture of the scoured render and thereby allows the pattern to be clearly seen, this skim was applied at an average thickness no greater than 1mm.

The pattern is quite dense in its detail and actually takes up about 40% of the surface area of the render and so took nearly 45 mandays to complete.

We hope to develop these techniques further and believe that we can create designs such as company logos or slogans and that it is a fantastic way of decorating the surface of large areas of render, it is indeed a modern variation on  pargetting and sgraffito to march hand in hand into the future with modern limes and modern architectural designs

Advertisements

About byrnesurfaces

conserver and repairer of historic surfaces
This entry was posted in decorated plaster, Lime Plaster, technical stuff, Uncategorized and tagged , , , , . Bookmark the permalink.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s